Labor Day Sailing (2008)

It's been a busy year and we haven't had time to get back out on the water... After a couple frustrating sailing trips last summer I decided to redesign the sail and buy an electric trolling motor. So on Labor Day we decided to take the sailboat out for the first time this year!

The trolling motor is a WONDERFUL addition and well worth the $109. We spent about 3 hours exploring some nearby islands around Harrison Bay. We also went swimming, explored a couple quiet coves and got sunburned! It was awesome!

What I've Learned...

This has been a very busy summer for us and we've only managed to take the boat out twice so far. Our second time out on the water was a bit scary due to the gusty winds... Anyway, having spent some time in the boat now, I've made a list of things that I've learned:

• Exterior latex house paint doesn't work very well on a boat (I repainted it with oil paint after the latex started peeling off).
• Make sure wood filler is water proof once it dries. Perhaps bondo would have been better to use...
  
• A 12ft boat isn't very big. Mine only holds 3 people (I haven't tried 4 yet, but 3 is pretty crowded).
• Backing the boat into the water is much easier than carrying the boat to/from the water.
  
• I need to redesign my sail because my current sail puts too much stress on the mast.
• Unless you have all the right sailing hardware (for the ropes, etc.) it's a lot of work!
• I need to get some sort of motor (for times when there's no wind). I'm looking into getting an electric trolling motor.
  

The Maiden Voyage

This morning we set sail with the Nellie Sue on her maiden voyage on Chickamauga Lake. The wind wasn't very strong so we didn't go very fast but we did manage to get out in the middle of the lake where we jumped in and swam. The heat index for today was 108 degrees, so the water felt VERY refreshing!

After our swim, we had a picnic lunch and sailed back to the beach from wenst we saileth. Here are a few more still pictures of our sailing trip.

Thanks to Todd for taking these last two pictures for us.

It's Finally Finished!

Tonight we pulled the boat out onto the lawn and assembled the mast & sail for the very first time! I wanted to make sure everything worked the way it was supposed to and that I had all the correct parts before we hit the water...

It really does look like a sailboat now! Maybe not necessarily like the stereotypical triangular sail sailboat, but nevertheless I am still very proud of my little boat!

Earlier this evening I went to go check out a trailer that was for sale -- I'll probably end up buying it. Tomorrow I'm getting a trailer hitch installed on my car, so hopefully by this weekend I'll be ready and equipped to go sailing!

If you're interested in watching the maiden voyage with me, just send me an email and I'll let you know when and where to meet.

Registration, Rudder and Tiller

Woohooo! My boat is officially registered and legal to be out on the open water! With the registration process and rudder completed, it's essentially finished!

On Friday I left work early and swung by the Tag & Title office. After waiting in line for about 20 minutes with people who were standing just a little bit too close to me, I finally was able to do my registration paperwork and pay the tax fees - $2. Since it's a homemade boat, there's actually no sales tax to pay! The $2 was to cover the processing fees. :)

So then I had to mail in a check for $28 along with the registration papers to get my 3-year boat license and registration card. But until then I can still legally go boating. I just have to keep my registration receipt with me. And again I say, "Woohooo!" . :)

On Sunday I finished building & painting the rudder and tiller. I had to fabricate some kind of hinge mechanism for the rudder which I made from pieces of metal strips which I bent into shape with a vice and a hammer. It was tough work, but it turned out very well!

I then attached nylon rope cleats to the sides of the boat, and some metal rings to the back of the boat. The rings are to either tow my little inflatable raft behind me, or to tie the boat down during transportation.

Rudder & Tiller

Yesterday I painted the rudder (first coat) and made a tiller -- the long handle connected to the rudder that steers the boat. I didn't have any clear instructions on how to make the tiller, so I did some research online and saw a variety of styles. So I decided to take the sturdy but yet easy-to-build rout. It's not necessarily pretty, but it will do the job.

The fork part of the tiller will go around the top part of the rudder and will pivot on a pin so I can raise and lower the handle to the desired height. I now just need to figure out how to attach the rudder to the boat...

Here are a couple photos of the boat in it's current state, the daggarboard on the wall, and the 4 new life jackets. Janell and I plan to get nicer life jackets for the two us. These standard orange boxy ones are just the cheep loaner life jackets for guests. :)

Building the Sail

Today I painted another coat of paint to the inside of the boat, made a few additions to the mast components, and built the sail! I'm so excited now! I could practically drop it in the water today and go sailing... but I do need to connect the rudder and finish getting the boat registered first.

To make the sail, I took a 12'x12' sheet of 3mil plastic and stretched it out on the garage floor, taping the corners down with duct tape. Then I measured out all the sides of the sail, and taped the rope into place. Then I folded the plastic over the rope and ran a layer of duct tape along the seam -- front and back.

Then I added reinforcement strips of duct tape within the sail area, and reinforced the corners. I'm quite impressed with how it turned out. It doesn't look bad at all, especially considering that it's just plastic and duct tape! .... :)

Thank You!

I just wanted to say a special Thank You to those of you who have been faithfully following my progress over the past 9 months. Your comments have been very encouraging to me and have kept me continually moving forward. It would have been a much longer process without you!

You have an open invitation to go sailing with me any time (once the boat is finished of course)! . :)

Boat Registration [part 2]

[Three weeks later...]

Woohoo! I now have the Hull Identification Numbers for my boat! Now I just need to swing by the DMV and finish up the registration process and get this thing out on the lake. I'm getting so close I can almost smell the fishy water. Mmmmmm.... :)

However, I still need to:

• make a sail
• install all the necessary hardware on the mast
• finish up & connect the rudder
• paint the final coat on the boat

...but this all shouldn't take but a couple days.

Boat Registration [part 1]

I just got off the phone with the Tennessee Wildlife Enforcement Agency (TWEA) and in typical government fashion I was transfered to a new person about 7 times (explaining why I'm calling each time) before I finally reached the correct person, only to get their voicemail!!! Grrrrrr!

Apparently to register a homemade boat (without a bill of sale) you have to go through their main office in Nashville. They assign you a hull number and then send the information to the Chattanooga office who then sends someone out to inspect the boat. Or maybe you have to go to them... not sure... Then after filling out all the required forms with them, you have to jump through the DMV's hoops (i think). *sigh*

[a couple hours later...]

I finally got a call from the guy in Nashville who emailed me a form to fill out. I did, and it is now in the mail. That wasn't too difficult. I just hope the rest of the registration process will be as painless!

And Then There Was Color

OK, so the maiden voyage hasn't happened yet...

But, I finally put a coat of color on the boat! It feels like it's getting so close now. I also painted the inside of the boat and the top of the bow. I'll post pictures of that after the paint dries and I can flip it over again.

I also cut out and glued the layers of plywood together to build the rudder. Now I just need to make the tiller (for the rudder) and make the sail... Oh, and register the boat.

P.S. I now also have life jackets!

Oh, and "happy 4th of July week" to all you Americans who care. In my previous post I mentioned that it was Memorial Day, so thought it was only fair to also mention the 4th in this one. :)

Paint It White

This week I put on the base coat of white exterior latex paint. I read somewhere that exterior latex paint was as good as (or better than) oil-based paint for boats, so I thought I'd give it a shot. Once it dries it becomes as waterproof as the oil based paint, and will actually last longer because it won't dry out and crack like oil paint will.

This is Memorial Day weekend, so I might actually shoot for a maiden voyage...

Stay tuned.

P.S. This is the color-scheme we're thinking of painting our boat.

Daggerboard and Mast

As you probably noticed I quit keeping track of how many days I was working on the boat. I kind of got out of sync and lost count and gave up...

...but maybe that's a good thing because I've been making good progress! This Spring weather has been awesome (except for a week or so ago when it got down into the 20's and killed all our baby peaches and other flowering plants).

Since my last post I:
~ Filled cracks and holes with latex caulking and wood filler.
~ Sanded down rough edges with my Drimmel tool.
~ Built the daggerboard and daggerboard handle.
~ Shaped the mast pieces (by using a hand planer to make the the mast narrower at the top and adding pieces of wood, canvas and epoxy to make it thicker at the base).

I am guessing I have about 2 more weeks worth of work before the boat is ready for it's maiden voyage! :)

Day "whatever"

I've been very bad at documenting my progress on the boat and have done quite a bit of work since my last post... I don't know where to begin.

The cold weather of winter kept me in-doors for several months and when it finally started getting warm again I started working as fast and efficiently as I could, and in the excitement I forgot to post pictures! Oh well, I think there are only 2 or 3 people who are actually following this blog. =)

(pssst! Post a comment so I'll know who's appreciating my hard work.)

Ok, here are some recent photos of the boat.

Above: Rear seat and storage compartment.


Above: I wasn't following the plans and had to build the bow twice... (before and after)


Above: Me demonstrating how big (or small) the boat is.


Above: The skeeg and rub rails. Polyurethane foam to seal all the cracks around the seats, etc.

I Haven't Given Up!

Several of you have told me that you've noticed that progress on the boat seems to have stopped... No, I haven't given up on my boat project. Sadly it is still winter here in Tennessee and my little workshop has no heat so I've put things on hold momentarily. The past several weeks have been near or below freezing at night and the workshop doesn't heat up much during the day.

Trust me, the first warm day we get and I'll be out there! In fact today was almost warm enough...

~E

Day 18 - Rails and Seat

On Sunday the weather was unusually warm for this time of winter. It was actually up in the 70's! ...so I decided to spend some time working on my boat.

It's hard to believe that it's already been nearly a month since I last tinkered on the boat. The holidays really threw a wrench in the work flow... but now things are slowing down once again and I am able to find some free time to "play".

So anyway, on Sunday I decided to cut out the middle seat and work on attaching a few more rub rails to the bottom and sides of the boat. After cutting out the seat I discovered that my measurements had been somewhat incorrect, so I had to make a couple more cuts. Luckily it was still usable so it wasn't a total failure. I glued and screwed some small one-by's to the underside of the seat to add a little strength and then fastened the seat to the boat.

Then I cut a couple pieces of molding and filed down the ends to smooth them off before gluing and screwing them to the bottom of the boat. These rails will not only add more rigidity to the bottom of the boat, but will also protect it against rocks or logs, etc... I also added some small rails along the side... more for looks than for anything else.

Yesterday I went out to take some photos of the boat (around 5:30pm) and the temperature inside my workshop was 35 degrees -- two days ago it was in the low to mid 70s.





~E